Verified NS0-183 exam dumps Q&As with Correct 145 Questions and Answers
Network Appliance NS0-183 Test Engine PDF - All Free Dumps from PremiumVCEDump
Network Appliance NS0-183 Exam Syllabus Topics:
| Topic | Details |
|---|---|
| Topic 1 |
|
| Topic 2 |
|
| Topic 3 |
|
| Topic 4 |
|
| Topic 5 |
|
| Topic 6 |
|
| Topic 7 |
|
| Topic 8 |
|
NEW QUESTION 42
Click the Exhibit button.
You are reviewing the setup of a recently installed FAS9000 switched cluster. As shown in the exhibit, the cluster interconnects are connected to a pair of Cisco Nexus 3132Q-V 40 Gb ports.
For a high availability, which ports should swap Ethernet cables?
- A. Swap node1:e4a and node1:e8a.
- B. Swap node1:e4a and node2:e4b.
- C. Swap node2:e4a and node2:e8a.
- D. Swap node1:e8a and node2:e4a.
Answer: C
NEW QUESTION 43
One of the nodes in your ONTAP 9.7 cluster has failed and is not coming back online.
Which two methods would you use to connect to the node failing to come back online? (Choose two.)
- A. Use the Intelligent Platform Management Interface.
- B. Use the Service Processor Interface.
- C. Use Secure Shell.
- D. Use Telnet.
Answer: B,C
NEW QUESTION 44
Before starting a base installation on an AFF A400, you need to find out the default cluster interconnect ports for the AFF A400 controllers.
In this scenario, which three resources would you use to find this information? (Choose three.)
- A. Interoperability Matrix Tool (IMT)
- B. hardware installation setup poster
- C. Hardware Universe (HWU)
- D. Active IQ Unified Manager
- E. AFF FAS Documentation Center
Answer: B,C,E
NEW QUESTION 45
You have an AFF All SAN Array (ASA) cluster that is running ONTAP 9.7. The cluster is configured for Active Directory domain controller access using a domain tunnel.
In this scenario, which two licenses are enabled on the cluster? (Choose two.)
- A. FCP
- B. iSCSI
- C. CIFS
- D. NVMe
Answer: A,C
NEW QUESTION 46
What is the maximum number of data disks that a RAID-TEC RAID group has?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: D
NEW QUESTION 47
Click the Exhibit button.
You are installing a new FAS cluster. The management network must be on tagged VLAN 11 for remote administration by a service provider.
Referring to the exhibit, which two ports will allow service provider access to both cluster and node management LIFs? (Choose two.)
- A. e0a-11
- B. e0b-11
- C. e0M-11
- D. e0M
Answer: C,D
NEW QUESTION 48
During handover, a customer asks you how to obtain support from NetApp after installation.
What are two responses in this scenario? (Choose two.)
- A. Send an AutoSupport message from the system.
- B. Visit.
- C. Contact Global Support by telephone.
- D. Visit mysupport.netapp.com
Answer: C,D
NEW QUESTION 49
After an initial setup, you want to create a new data aggregate. The node has thirty-one 4 TB SATA spare disks assigned. Your customer wants to have two spare disks.
In this scenario, which two settings would you use to reach the maximum capacity and availability? (Choose two.)
- A. -maxraidsize 29
- B. -maxraidsize 31
- C. -raidtype raid_dp
- D. -raidtype raid_tec
Answer: A,D
NEW QUESTION 50
Which LIF type is used by default for hardware-assisted storage failover communication?
- A. intercluster
- B. data
- C. cluster-mgmt
- D. node-mgmt
Answer: D
NEW QUESTION 51
You are using a NetApp CN1610 cluster-interconnect switch and need to connect a new AFF A800A node to the switch.
In this scenario, how many Ethernet ports per node are required on each switch?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: B
NEW QUESTION 52
An administrator is installing a new AFF A220 HA pair and needs to convert two unified target adapter (UTA) ports from converged network adapter (CNA) to FC.
In this scenario, which action sequence will accomplish this task?
- A. 1. Set the adapter to status-admin down. 2. Reboot the node. 3. Set the port mode to fc. 4. Set the adapter to status-admin up.
- B. 1. Set the adapter to status-admin down. 2. Set the port mode to fc. 3. Set the adapter to status-admin up. 4. Reboot the node.
- C. 1. Set the adapter to status-admin down. 2. Set the port mode to fc. 3. Reboot the node. 4. Set the adapter to status-admin up.
- D. 1. Set the port mode to fc. 2. Set the adapter to status-admin down. 3. Reboot the node. 4. Set the adapter to status-admin up.
Answer: C
NEW QUESTION 53
Which keyboard combination enables you to access the Service Processor (SP) or the Board Management Control (BMC) from the system console CLI?
- A. Ctrl + D
- B. Ctrl + G
- C. Ctrl + C
- D. Ctrl + S
Answer: B
NEW QUESTION 54
After you install a new cluster with ONTAP 9.5 software, you want to create a new broadcast domain. During the creation of the broadcast domain, you receive an error that there are no free ports available.
What is the reason for this error message?
- A. You can create a new broadcast domain only within the CLI.
- B. Before you configure a new broadcast domain, you should create a new IPspace.
- C. By Default, all ports are bound to the "Default" broadcast domain. To create a new port, remove the needed ports from the "Default" broadcast domain.
- D. By Default, all ports are bound to the "Default" broadcast domain. To create a new port, remove the needed ports from the "Default" broadcast domain and create a new IPspace.
Answer: C
NEW QUESTION 55
You installed a new AFF A800 2-node ONTAP 9.5 cluster and are asked to run diagnostics to validate the hardware.
Which command is used from the loader prompt to enter diagnostics?
- A. savenv
- B. boot_diags
- C. printenv
- D. sldiag
Answer: B
NEW QUESTION 56
After you deploy a 4-node AFF A220, you want to upgrade the ONTAP version of the cluster.
In this scenario, before the upgrade, which advanced CLI command is used to locate epsilon?
- A. cluster ha show
- B. clustering ring show
- C. cluster image show
- D. cluster show
Answer: D
NEW QUESTION 57
You are installing a pair of Cisco Nexus 3132Q-V cluster switches and receive several syntax errors when the reference configuration file (RCF) is applied.
In this scenario, what are two reasons for these errors? (Choose two.)
- A. Cables were not removed before applying the RCF.
- B. An RCF file for a different version has been loaded.
- C. The switch was not in maintenance mode.
- D. The RCF was already applied.
Answer: B,D
NEW QUESTION 58
Which statement regarding Epsilon is true?
- A. The epsilon acts as a tiebreaker in a 2-node cluster.
- B. Epsilon is reassigned automatically to the HA partner in case the current owner of the epsilon suddenly reboots.
- C. The node holding the epsilon has extra fractional vote weight.
- D. Whenever a new node is added, the epsilon is automatically reassigned to this node.
Answer: C
NEW QUESTION 59
You install a new FAS2650 HA with a DS224C disk shelf and ONTAP 9.5 on a customer site.
Referring to the exhibit, which steps are required to get an HA cabled system?
- A. 1. Insert a cable from right controller port 0a to IOMB port 2, and from port 0b to IOMA port 4. 2. Insert a cable from left controller port 0a to IOMA port 2, and from port 0b to IOMB port 4. 3. Cable the out-of-band ACP.
- B. 1. Insert a cable from right controller port 0a to IOMB port 1, and from port 0b to IOMA port 4. 2. Insert a cable from left controller port 0a to IOMA port 1, and from port 0b to IOMB port 4. 3. Cable the out-of-band ACP.
- C. 1. Insert a cable from right controller port 0a to IOMA port 1, and from port 0b to IOMB port 3. 2. Insert a cable from left controller port 0a to IOMB port 1, and from port 0b to IOMA port 3.
- D. 1. Insert a cable from right controller port 0a to IOMB port 2, and from port 0b to IOMA port 3. 2. Insert a cable from left controller port 0a to IOMA port 2, and from port 0b to IOMB port 3.
Answer: C
NEW QUESTION 60
Which tool allows you to create a new FlexGroup volume?
- A. Cluster Config Builder
- B. OnCommand Unified Manager
- C. NetAppDocs
- D. OnCommand System Manager
Answer: D
NEW QUESTION 61
Before installing an 8-node cluster for a customer, you want to validate compatibility with existing hardware.
Which two tools would you use to validate the configuration? (Choose two.)
- A. Hardware Universe
- B. Active IQ System Manager
- C. Interoperability Matrix Tool
- D. Active IQ Config Advisor
Answer: C,D
NEW QUESTION 62
......
100% Passing Guarantee - Brilliant NS0-183 Exam Questions PDF: https://www.premiumvcedump.com/NetworkAppliance/valid-NS0-183-premium-vce-exam-dumps.html