350-501 PDF Dumps 2025 Exam Questions with Practice Test
Dumps for Free 350-501 Practice Exam Questions
Cisco 350-501 certification exam is ideal for professionals looking to advance their careers in the service provider industry. Implementing and Operating Cisco Service Provider Network Core Technologies certification validates the skills required to implement and operate complex service provider networks, making candidates highly sought after by employers. Implementing and Operating Cisco Service Provider Network Core Technologies certification is also an excellent way for candidates to showcase their expertise and differentiate themselves in the highly competitive job market. Passing the Cisco 350-501 certification exam is a significant achievement that demonstrates a candidate's commitment to professional development and growth in the field of service provider network technologies.
Candidates for the Cisco 350-501 Exam
The candidates who should take the Cisco 350-501 exam occupy different positions such as network administrators or engineers. Also, it is helpful for system engineers and network managers. Another category of the target audience for this test is formed of network designers and project managers.
The exam-takers will have 120 minutes to answer the questions included in the test. Nonetheless, Cisco doesn’t give too much information on the process itself. However, the candidates should expect to find multiple-choice and multiple-answer as well as drag and drop questions. In any case, its difficulty level is quite high, which means that students should be thoroughly prepared.
NEW QUESTION # 234
What causes multicast traffic to permanently stay on the shared tree and not switch to the source tree?
- A. SSM range is being used.
- B. The RP IP address is configured incorrectly.
- C. The SPT threshold is set to infinity.
- D. The RP announcements are being filtered.
Answer: D
Explanation:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/mcst_ovr.ht ml
NEW QUESTION # 235
Drag and drop the functionalities from the left onto the target fields on the right.
Answer:
Explanation:
NEW QUESTION # 236
Drag and drop the functionalities from the left onto the target fields on the right.
Answer:
Explanation:
NEW QUESTION # 237
Which utility can you use to locate MPLS faults?
- A. EEM
- B. QoS
- C. MPLS LSP ping
- D. MPLS traceroute
Answer: C
NEW QUESTION # 238
Which control plane protocol is used between Cisco SD-WAN routers and vSmart controllers?
- A. BGP
- B. UDP
- C. OTCP
- D. OMP
Answer: D
NEW QUESTION # 239
What do Ansible and Salt Stack have in common?
- A. They both can be designed with more than one master server
- B. They both use DSL configuration language
- C. They both use YAML configuration language
- D. They both have agents running on the client machine
Answer: A
NEW QUESTION # 240
Refer to the exhibit:
This configuration is being applied on an IOS XR router.
Which statement about this configuration is true?
- A. It is used to set up configuration to poll network data
- B. It is used to enable gRPC
- C. It is used to create a streaming subscription with a 60-second interval
- D. It is used to create a streaming subscription with a 600-second interval
Answer: C
NEW QUESTION # 241
Refer to the exhibit.
Refer to the exhibit an engineer working for a private telecommunication company with an employee Id: 4065:96:080 upgrades the WAN link between routers ASBR-101 and ASBR-201 to 1Gb by Installing a new physical connection between the Gi3 Interfaces. Which BGP attribute must the engineer configure on ASBR-201 so that the existing WAN link on Gi2 Is maintained as a backup?
- A. Option A
- B. Option C
- C. Option B
- D. Option D
Answer: B
NEW QUESTION # 242
Refer to the exhibit:
With which router does IOSXRV-1 have LDP session protection capability enabled but session hold up is not active?
- A. 192.168.0.4
- B. 192.168.0.1
- C. 192.168.0.3
- D. 192.168.0.5
Answer: C
NEW QUESTION # 243
Which statement describes the advantage of a Multi-Layer control plane?
- A. It automatically provisions monitors, and manages traffic across Layer 0 to Layer 3
- B. It minimizes human error configuring converged networks
- C. It provides multivendor configuration capabilities for Layer 3 to Layer 1
- D. It supports dynamic wavelength restoration in Layer 0
Answer: A
Explanation:
A Multi-Layer control plane, like Cisco's nLight technology, provides an integrated approach that allows for the automatic provisioning, monitoring, and management of traffic across different network layers, from Layer 0 (optical) to Layer 3 (IP). This integration increases network agility and flexibility while improving network utilization, leading to significant cost savings and more efficient network resiliency solutions2.
The Economics of Cisco's nLight Multilayer Control Plane Architecture2.
NEW QUESTION # 244
Drag and drop the functions from the left onto the Path Computation Element Protocol roles on the right.
Answer:
Explanation:
NEW QUESTION # 245
Refer to the exhibit. R101 is peering with R102 and R103, and R201 is peering with R202 and R203 using iBGP Labeled Unicast address families.
The OSPF area 0 border routers are in a full iBGP Labeled Unicast mesh, and VPNv4 routes are exchanged directly between PE routers R101 and R201 through iBGP.
Which address family-level configuration must be applied on ABR R102 on ABR R102 to support a Unified MPLS routing architecture with partitioned IGP domains?
- A.
- B.
- C.
Answer: C
NEW QUESTION # 246
Drag and drop the functions from the left onto the Path Computation Element Protocol roles on the right.
Answer:
Explanation:
Explanation
PCE - 1,2,5
PCC- 3,4
NEW QUESTION # 247
Refer to the exhibit:
A network engineer is implementing an OSPF configuration Based on the output, which statement is true?
- A. IPv6 routing not enabled" is just an informational message and OSPFv3 runs for IPv4 on interface FastEthernet0/0 anyway
- B. OSPFv3 does not run for IPv4 on FastEthemet0/0 until IPv6 routing is enabled on the router and IPv6 is enabled on interface Fastfc.thernet0/0
- C. OSPFv3 cannot be configured for IPv4; OSPFv3 works only for IPv6.
- D. In the ospfv3 1 area 1 ipv4 command, area 0 must be configured instead of area 1.
Answer: B
NEW QUESTION # 248
Refer to the exhibit.
Refer to the exhibit. A global company plans to implement BGP at its newest location to provide connectivity to other offices. The global infrastructure of the company is a multivendor environment. An engineer must review the BGP core configurations at headquarters to determine if they can be repurposed at the new location. The engineer copied this JSON script for review. What is the effect of the script?
- A. It sets the BGP router-ID to 192.168.1.2 and sets the AS of the router to 65514.
- B. It configures BGP on the device and inserts 192.168.1.0/24 into the BGP table using the origin AS 65514.
- C. It configures BGP with neighbor 192.168.1.2 residing in AS 65514.
- D. It configures a VRF named cisconode1 and a BGP instance using the VPNv4 address family.
Answer: C
NEW QUESTION # 249
A router is configured to perform MPLS LDP graceful restart.
Which three steps are included when the RP sends an LDP initialization to a neighbor to establish an LDP session? (Choose three)
- A. Reconnect Timeout field
- B. Recovery Time field
- C. Type-9 LSA
- D. Learn from Network (L) flag, set to 1
- E. Graceful restart capability in OPEN message
- F. Learn from Neighbor (N) flag, set to 1
Answer: A,B,D
Explanation:
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/mp_ha/configuration/xe-16-8/mp-ha-xe-16-8- book/nsf-sso-mpls-ldp-and-ldp-graceful-restart.html
NEW QUESTION # 250
Which module refers to the network automation using Ansible?
- A. the iosxr_user module to manage banners for users in the local database
- B. the iosxr_system module to collect facts from remote devices
- C. the iosxr_command module to issue run commands on remote devices
- D. the losxr_logging module to run debugging for seventy levels 2 to 5
Answer: C
Explanation:
https://docs.ansible.com/ansible/latest/collections/cisco/iosxr/iosxr_command_module.html#ansible-collections-cisco-iosxr-iosxr-command-module
NEW QUESTION # 251
Refer to the exhibit:
Which effect of this configuration is true?
- A. R1 can failover only to a peer that is configured for LDP SSO/NSF
- B. R1 can support a graceful restart operation on the peer, even if graceful restart is disabled on the peer
- C. R1 can failover to any peer
- D. R1 can support a peer that is configured for LDP SSO/NSF as the peer recovers from an outage
Answer: A
NEW QUESTION # 252
......
Nowadays, infrastructure, networking, and software have become more and more interrelated. Applications give new experiences, and with well-targeted networking, the service suppliers can use the automation to secure and scale their infrastructure. That is why many IT specialists pass the exams to obtain the certification(s) that will validate their skills. Thus, the CCIE Service Provider and CCNP Service Provider certificates can prove that you know about provider networking: from planning & designing to managing & optimizing. These certifications are presented by Cisco, and to earn them, the individuals have to complete the core test, which is 350-501 SPCOR. Besides that, they will be required to pass one concentration exam of their choice (there are 3 of them for CCNP Service Provider) or one practical lab test (for CCIE Service Provider).
Check your preparation for Cisco 350-501 On-Demand Exam: https://www.premiumvcedump.com/Cisco/valid-350-501-premium-vce-exam-dumps.html
350-501 Dumps PDF And Certification Training: https://drive.google.com/open?id=1EHRmhg1c4e8K0wcL7Th7JJrr8n1m_PNu